Avcon Technics Private Limited

Shivajinagar, Pune, Maharashtra


Send Email
0804841133991% Response Rate

Home » Products & Services » Micro Concrete Avcretemc60

Micro Concrete Avcretemc60

Our service range includes a wide range of micro concrete - avcrete mc 60.

Micro Concrete - Avcrete MC 60


Micro Concrete - Avcrete MC 60
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 1 / KgGet Latest Price

Service Details:
Packaging Size50 kg polythene lined bags
Fresh wet densityApprox 2350 kg per cum
Yield21 litres

Micro Concrete - Avcrete MC 60 does not contain any chlorides, sulphates, amorphous silica or harmful chemicals. With low permeability, it is known as superfluid microconcrete, widely applied for large section repairs ranging from 50 mm-200 mm. Depending on configuration of the repair, location and volume of exposed reinforcing steel, higher thicknesses can be achieved with this concrete.

  • Low alkali content minimizes risk of alkali-silica reaction
  • Offers an extremely high level of control of plastic and long-term drying shrinkage
  • Very low permeability
  • Suitable for large volume repairs
  • Higher thicknesses are achievable
  • Provides excellent protection against carbonation and chloride attack
  • Exceptional flow allows pumping or pouring into restricted locations
  • Self-compacting nature eliminates honeycombing and displaces air without vibration
  • Does not contain any chlorides, sulphates, amorphous silica or harmful chemicals.

  • Rigid, tight formwork should be used with properly sealed faces to prevent loss of material and to make sure that no water is absorbed from the repair material
  • Drainage outlets should be included in the formwork for pre-soaking
  • There should be a provision for air venting
  • There should be suitable access points to pour or pump the mixed micro-concrete into place
  • Break out the complete repair area to a minimum depth of 50mm
  • Remove ant dust, unsound or surface contamination from the surface
  • The surface must be roughened and any laitance must be removed by hacking, chipping or sand / grit-blasting
  • Expose fully any corroded steel in the repair area and remove all corrosion deposits
  • Steel should be cleaned to a bright condition

  • Shutter or material should not be vibrated
  • Light, but not excessive tapping of the shutters is permitted

  • Until the compressive strength of 10 mpa is achieved, the formwork should be left in place
  • In case of fast drying conditions, supplementary curing with polythene sheeting taped down at the edge is recommended
  • After the strapping of formwork, any kind of delay in the curing process will have adverse effects on the product performance

Shelf life:
  • Storage conditions- cool and dry place at temperatures between 5 C and 35 C
  • Expected shelf life- 6 months (in case it is a sealed bag and protected from high temperatures and high relative humidity)

Technical description:
Compressive Strength N/mm23 days33 Mpa
IS: 516-19597 days55 Mpa
IS: 456-200028 days80 Mpa
Flexural Strength28 days8.9 Mpa
Bond strength in slant shear- substrate pre-soaked, No bonding aid28 days50 Mpa
Flow properties> 1000mm in 4-10 Secs( initial) >850mm in 5-15 secs (after 15 minutes)
Fresh wet densityApprox. 2350 kg per cum
Setting time: initial Set: Final Set:4 hours, 8 hours
Yes! I am Interested


Explore More Services

Contact via E-mail
Contact via SMS
Smita Sathe (Sales & Marketing)
Avcon Technics Private Limited
Office No. 103 - 105, Sheetal Plaza, Plot No. 499, Model Colony, Shivajinagar
Pune - 411016, Maharashtra, India
Call Us: 
Call Response Rate: 91%
Share Us :

Home  |   Profile   |  Products & Services  |  Site Map  |   Contact Us

© Avcon Technics Private Limited. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited

Avcon Technics Private Limited